Charging

Step 1. Install the battery into the charger

1. Lift the lever (C) of the charger.
2. Remove the protective cover from the Battery Pack.
3. Install the Battery Pack into the charger.
4. Click the lever (C).

Step 2. Сheck the current battery level

• Upon installation, a green LED indicator (D) on the charger will start to glow and begin flashing:

– once if the battery charge ranges from 0% to 50%;

– twice if the battery charge ranges from 51% to 75%;

– three times if the battery charge ranges from 76% to 100%;

• If the indicator lights green continuously, the battery is fully charged.
• You can remove the battery from the charger by lifting the lever (С).
• If the indicator of the charger lights red continuously upon battery installation, probably the battery’s charge level is lower than acceptable (the battery has been long in deep discharge). Keep the battery in the charger for a long time (up to several hours), remove and re-insert it.
• If the indicator starts blinking green, the battery is good.
• If the indicator keeps lighting red, the battery defective. Do not use the battery!

The LED indicator (D) will display the battery charge status:

LED Indicator	Battery Charge Status
	Battery is empty
	Battery is full

Step 3. Сonnect the charger to the mains supply

1. Connect the Micro-USB plug of the USB cable to the port (E) of the charger.
2. Connect the Micro-USB plug to the power adapter.
3. Insert the plug of the power adapter to the 100-240 V socket.

The device can be powered with an external power supply such as Power Bank (5 V).

1. Connect the external power supply to the USB port (15) of the device.
2. The device switches to operation from external power supply, and the IPS7 Battery Pack will begin slowly charging.
3. The display will show the battery icon  with charge level as a percentage.
4. If the device operates on external power supply but the IPS7 battery is not connected, icon  is shown.
5. When the external power supply is disconnected, the device switches to the internal battery pack without powering off.

Warning! Charging IPS7 / IPS14 batteries at air temperatures below 0° C (32° F) may reduce battery life. When using external power, connect the Power Bank to the device after it has been turned on and working for several minutes.

1. Lift the lever (10).
2. Install the battery (9) all the way into the dedicated slot on the device housing so that element F appears from below.
3. Fix the battery by clicking the lever (10).

The quick menu allows change of basic settings such as display brightness and contrast, smooth digital zoom.

• Enter the menu with a short press of the Мenu (3) button.
• To toggle between the functions below, press successively the Menu (3) button.

Brightness  – press briefly the UP (2)/DOWN (5) buttons to change display brightness from 0 to 20.

Contrast  – press briefly the UP (2)/DOWN (5) buttons to change display contrast from 0 to 20.

Base mode  – it allows you to select one of the three observation modes (Forest, Rocks, Identification) as a base for the User mode.

Smooth digital zoom  – press the UP (2)/DOWN (5) buttons to change digital zoom from 2.5 to 20.

Smooth digital zoom is in 0.1x increments.

• To exit quick menu, press and hold down the Menu (3) button or wait 5 sec for automatic exit.

The status bar at the bottom of the display shows current operating statuses via icons, including:

1. Color palette (shown only if the “Black Hot” palette is selected)
2. Observation mode
3. Calibration mode (in the automatic calibration mode, three seconds before automatic calibration a countdown timer  is shown in place of the calibration mode icon).
4. Current full magnification (for example, 16x)
5. Wi-Fi connection status
6. Time
7. Power indication:

• Battery charge level  (if the device is powered by the Battery Pack).
• External battery power indicator  (if the device is powered by an external power supply).

The device allows you to quickly increase the basic magnification (please refer to the Magnification line in the Specifications table) by 2, 4 or 8 times.

• To operate the discrete digital zoom, press successively the DOWN (5) button.
• The digital zoom will not be saved after the device is re-started.

Calibration eliminates image flaws (such as vertical bars, phantom images, grainy field of view, etc.) by equalizing the microbolometer background temperature.

There are three calibration modes: manual (M), semi-automatic (SA) and automatic (А).

Select the desired mode in the menu option Calibration Mode .

Mode М (manual)

• Close the lens cover.
• Press briefly the ON/OFF (1) button.
• Open the lens cover.

Mode SA (semi-automatic)

• Press briefly the ON/OFF (1) button to calibrate.
• You do not need to close the lens cover (the microbolometer is closed with the internal shutter automatically).

Mode А (automatic)

• The device calibrates by itself according to the firmware algorithm.
• You do not need to close the lens cover (the microbolometer is closed with the internal shutter automatically).
• In the automatic mode, the user can calibrate the microbolometer with the ON/OFF (1) (in the SA mode) button.
• In the automatic calibration mode, three seconds before automatic calibration a countdown timer  is shown in place of the calibration mode icon.

1. Open the lens cover (13).
2. Turn the device on with a short press of the ON/OFF (1) button.
3. Adjust the interpupillary distance with the rings (6) by moving the eyepieces farther or closer to each other.
4. To obtain a crisp image of the icons on the display, rotate the diopter adjustment ring (7). Once adjusted, there is no need to rotate the diopter adjustment ring for distance or any other conditions.
5. To focus on the object being observed rotate the lens focusing ring (8).
6. Select the calibration mode: manual (M), semi-automatic (SA) or automatic (A) in the main menu (enter the menu by long pressing the MENU (3) button).
7. Calibrate the image with a short press of the ON/OFF (1) button  (when calibration mode (SA) or (M) has been selected). Close the lens cap before manual calibration.
8. Select the desired observation mode (Forest, Rocks, Identification or User) by a long press of the DOWN (5) button or in the main menu. User mode allows you to configure and save custom
9. To set up display brightness and contrast and continuous zoom, please refer to the Quick Menu Functions section.
10. After use, press and hold down the ON/OFF (1) button to turn the device off.

Warning! Never point the lens at intensive energy sources such as laser radiation emitting devices or the sun. It can damage electronic components in the device. The warranty does not cover damage arising from failure to comply with operating instructions.

Warning! The radiator cooling system (12) becomes warm during operation: this is normal and allows an increase in the sensitivity of the device.

1. Press and hold down the Мenu (3) button to enter the main menu.
2. Select option General Settings  with the UP (2)/DOWN (5) buttons.
3. Press briefly the Мenu (3) button to confirm.

The following settings are available:

Language 

Selecting interface language

1. Select option Language  with the UP (2)/DOWN (5) buttons.
2. Press briefly the Мenu (3) button to confirm.
3. Select one of the available interface languages with a short press of the UP (2)/DOWN (5) buttons: English, French, German, Spanish, Russian.
4. Press briefly the Мenu (3) button to confirm.

Date

Date setup

1. Select option Date  with UP (2)/DOWN (5) buttons.
2. Press briefly the Мenu (3) button to confirm. Date format is displayed as: YYYY/MM/DD (year/month/day)
3. Select the correct values for the year, month and date with a short press of the UP (2)/DOWN (5) buttons.
4. Switch between digits with a short press of the Мenu (3) button.
5. Save selected date and exit the submenu with a long press of the Мenu (3) button.

Time

Time setup

1. Select option Time  with UP (2)/DOWN (5) buttons.
2. Press briefly the Мenu (3) button to confirm.
3. Select the desired time format with a short press of the UP (2)/DOWN (5) buttons: 24 or PM/AM.
4. Switch to hour setup with a brief press of the Мenu (3) button.
5. Select hour value with a brief press of the UP (2)/DOWN (5) buttons.
6. Switch to minute setup with a brief press of the Мenu (3) button.
7. Select minute value with a brief press of the UP (2)/DOWN (5) buttons.
8. Save selected time and exit the submenu with a long press of the Мenu (3) button.

Units of Measure

Selection of units of measurement

1. Select option Units of Measure  with UP (2)/DOWN (5) buttons.
2. Press briefly the Мenu (3) button to confirm.
3. Select the desired unit of measurement – meters or yards – with UP (2)/DOWN (5) buttons.
4. Press briefly the Мenu (3) button to confirm.
5. Exit to general settings submenu takes place automatically.

Default Settings

Restore default settings

1. Select option Default Settings  with UP (2)/DOWN (5) buttons.
2. Press briefly the Мenu (3) button to confirm.
3. With a short press of the UP (2)/DOWN (5) buttons select “Yes” to restore default settings or “No” to abort.
4. Confirm selection with a brief press of the Мenu (3) button.
   • If “Yes” is selected, display will show “Do you want to restore default settings?” and “Yes” and “No” options. Select “Yes” to restore default settings.
   • If “No” is selected, action is aborted and you return to the submenu.

The following settings will be restored to their original values before changes made by the user:

• Video recorder mode – video
• Observation mode – forest
• Calibration mode – automatic
• Language – English
• Mictophone – off
• Wi-Fi – off (default password)
• Magnification – off (no digital zoom)
• PiP – off
• Color mode – White Hot
• Unit of measurement – metric

Warning: date and time settings, default pixel map and remote control activation are not restored.

Format

This item allows you to format the Flash-card (memory card) of the device (this will delete all files from the memory card).

1. Select option Format  with UP (2)/DOWN (5) buttons.
2. Press briefly the Мenu (3) button to confirm.
3. With a short press of the UP (2)/DOWN (5) buttons select “Yes” to format the memory card or “No” to return to the submenu.
4. Confirm selection with a short press of the Мenu (3) button.
   • If “Yes” is selected, display will show “Do you want to format memory card?” and “Yes” and “No” options. Select “Yes” to format the memory card.
   • If “No” is selected, formatting is aborted and you return to the submenu.

This menu option allows you to set up your device for operation in a Wi-Fi network.

1. Press and hold down the Menu (3) button to enter the main menu.
2. Select the Wi-Fi Settings  menu option with the UP (2)/DOWN (5) buttons.
3. Press briefly the Menu (3) button to enter submenu.
4. Select the desired menu item with the UP (2)/DOWN (5) buttons.

Password Setup

This menu option allows you to set a password to access your binoculars from an external device.

The password is used to connect an external device (i.e. smartphone) to your thermal imager.

1. Press briefly the Menu (3) button to enter the Password Setup  submenu.
2. The default password (12345678) will appear on the screen.
3. Set the desired password with the UP (2)/DOWN (5) buttons.
4. Switch between digits with a short press of the Menu (3) button.
5. Save the password and exit the submenu with a long press of the Menu (3) button.

Access Level Setup

This menu option allows you to set required access level of the Stream Vision application to your device.

• Access level Owner. The Stream Vision user has the complete access to all device’s functions.
• Access level Guest. The Stream Vision user has the access only to the real time video stream from the device.

1. Press briefly the Menu (3) button to enter the Access Level Setup  submenu.
2. Select the access level with the UP (2)/DOWN (5) buttons.
3. Press and hold the Menu (3) to confirm your selection and exit from the submenu.

Selection of the Picture in Picture Mode

1. Press and hold the Menu (3) button to enter the menu.
2. Select the PiP Mode  option with the UP (2)/DOWN (5) buttons.
3. A short press of the Menu (3) button switches the mode on/off.

There are three calibration modes: manual (M), semi-automatic (SA) and automatic (А).

1. Press and hold down the Мenu (3) button to enter the main menu.
2. Select the Calibration Mode  option with the UP (2)/DOWN (5) buttons.
3. Press briefly the Menu (3) button to enter submenu.
4. Select the desired calibration mode with the UP (2)/DOWN (5) buttons.
5. Confirm your selection with a brief press of the Menu (3) button.

More details in the section Microbolometer Calibration.

Basic color mode is White Hot.

To select another palette:

1. Press and hold down the Мenu (3) button to enter the main menu.
2. Select the Color Modes  icon with the UP (2)/DOWN (5) buttons.
3. Press briefly the Menu (3) button to enter submenu.
4. Select the desired palette with the UP (2)/DOWN (5) buttons.
5. Confirm your selection with a brief press of the Menu (3) button.

• Black Hot (white color corresponds to low temperature, black color – to high temperature)
• Red Hot
• Red Monochrome
• Rainbow
• Ultramarine
• Violet
• Sepia

Note: to quickly change color modes press and hold the UP (2) button.

Icon brightness

1. Press and hold the Menu (3) button to enter the main menu.
2. Use the UP (2)/DOWN (5) buttons to select the Icon Brightness icon .
3. Press the Menu (3) button briefly to enter the submenu.
4. Use the UP (2)/DOWN (5) buttons to select the desired brightness level from 0 to 10.
5. Press the Menu (3) button briefly to confirm the selection.

The devices have four observation modes of the thermal imager: Forest (observation mode of objects within low thermal contrast conditions), Rocks (observation mode of objects within high thermal contrast conditions), Identification (high detalization mode), User (individual brightness and contrast settings).

1. Press and hold the Menu (3) button to enter the menu.
2. Select the Mode  option with the UP (2)/DOWN (5) buttons.
3. A short press of the Menu (3) button opens the menu.
4. Select one of the settings described below with the UP (2)/DOWN (5) buttons.
5. A short press of the Menu (3) button confirms the selection.

 Forest – This is the best mode when searching and observing within field conditions, against the background of leaves, bushes and grass. The mode is highly informative about an object being observed as well as landscape details.

 Rocks – This is the best mode when observing objects after a sunny day or within urban conditions.

 Identification – This is the best mode when observing objects within adverse weather conditions (fog, mist, rain and snow). It allows you to recognize the characteristics of an object being observed more clearly. Zoom increase may be accompanied by insignificant image graininess.

 User – It allows you to configure and save custom brightness and contrast settings, as well as one of the three modes (Forest, Rocks, Identification) as basic.

Note: to quickly change observation modes press and hold the DOWN (5) button.

The Image Detail Boost  function increases the sharpness of the contours of heated objects, which increases their detail. The result of the function depends on the selected mode and observation conditions: the higher the contrast of objects, the more noticeable the effect. This option is enabled by default, but can be disabled in the main menu.

Turn on/off Image Detail Boost:

1. Press and hold down the Мenu (3) button to enter the main menu.
2. Select the Image Detail Boost  menu option with the UP (2)/DOWN (5) buttons.
3. Turn Image Detail Boost on/off with a short press of the Мenu (3) button.

1. Press and hold down the Мenu (3) button to enter the main menu.
2. Select the Wi-Fi Activation  menu option with the UP (2)/DOWN (5) buttons.
3. Turn Wi-Fi on/off with a short press of the Мenu (3) button.

1. Enter the main menu with a long press of the Мenu (3) button.
2. Press the UP (2)/DOWN (5) buttons to switch between the menu options.
3. Enter a menu option with a brief press of the Мenu (3) button.
4. Exit the menu with a long press of the Мenu (3) button.
5. Automatic exit takes place in 10 sec of inactivity (buttons are not pressed).

General View of the Menu

Tab 1

Tab 2

This feature is not supported on devices manufactured after August 1, 2021.

Remote control activation (bought separately)

Before operating the remote control (RC), remember to activate it as follows:

1. Press and hold down the Menu (3) button to enter the main menu.
2. Select option Remote Control  with the UP (2)/DOWN (5) buttons.
3. Press briefly the Menu (3) button to confirm.
4. Display shows message “Wait” and countdown starts (30 sec), within which hold down for two seconds any RC button.
5. If activation is successful, the message “Connection complete” appears .
6. If error occurs the message “Connection failed” appears . Repeat the procedure.
7. The RC is activated and ready for use.
8. To unlink the RC, press the Menu (3) button, wait for the countdown to expire without pressing any RC button for 30 sec.
9. All remote controls previously linked to your device are now unlinked.
10. Now you can activate your RC again or activate another RC.

Menu item Rangefinder allows you to set up built-in rangefinder’s parameters as follows:

1. Enter the main menu with a long press of the Menu (3) button.
2. Select the submenu Rangefinder  with the UP (2)/DOWN (5) buttons.
3. Enter the submenu with a short press of the Menu (3) button.
4. Select the desired menu item with the UP (2)/DOWN (5) buttons.

Reticle Type

1. Select the Reticle Type  menu item with the UP (2)/DOWN (5) buttons.
2. Press briefly the Мenu (3) button to enter submenu.
3. Select one of the three reticle shapes  with the UP (2)/DOWN (5) buttons.
4. Confirm selection with a brief press of the Мenu (3) button.
5. Selected reticle will appear on the display.
6. The reticle will disappear from the display if the rangefinder is not used longer than 4 seconds.

TPA

Function “TPA” (Target Position Angle) allows you to measure the angle of target location (angle of elevation). When the function is activated, the angle is shown continuously.

1. Select TPA  with the UP (2)/DOWN (5) buttons.
2. Turn TPA on/off with a short press of the Мenu (3) button.

THD

“THD” (True Horizontal Distance) function allows you to measure true horizontal distance to a target based on the angle of elevation value.

1. Select THD  with the UP (2)/DOWN (5) buttons.
2. Turn THD on/off with a short press of the Мenu (3) button
3. Hereinafter the message THD will appear above the distance readings.

Turning on/off Microphone

This item allows you to enable (or disable) the microphone for recording sound during video recording.

1. Press and hold the Menu (3) to enter the main menu.
2. Select the Microphone  menu item with the UP (2)/DOWN (5) buttons.
3. To turn on the microphone, briefly press the Menu (3) button.  
4. To turn off the microphone, briefly press the Menu (3) button.  

The Display-Off function deactivates transmission of image to the display by minimizing its brightness. This prevents accidental disclosure. The device keeps running.

1. When the device is on, hold down the ON/OFF (1) button. Display goes out, message “Display off” appears.
2. To activate the display, press briefly the ON/OFF (1) button.
3. When you press and hold the ON/OFF (1) button, the display shows the message “Display off” with a countdown. Pressing & holding the button down for the duration of the countdown will power the device off completely.

The binoculars are equipped with a built-in rangefinder (17), allowing you to measure distance to objects up to 1000m away.

How the rangefinder works:

1. Turn on the device, set up image according to section Powering On and Image Setting.
2. Press the UP (2) or LRF (21) button on remote control – rangefinding reticle appears; in the top right corner of the display dashes of distance values with unit of measurement appear, i.e. the rangefinder enters the stand-by mode. 
3. If PiP mode is activated, the PiP window remains active upon activation of the rangefinder.
4. Point the rangefinding reticle at an object and press the UP (2) button.
5. In the top right corner of the display you will see distance in meters (or yards – depending on settings). 

Note: if the rangefinder is idle longer than for 4 seconds, it turns off automatically.

Operation in SCAN mode:

1. To measure distance in scanning mode, hold down the UP (2) or LRF (21) button on remote control for longer then two seconds. Measurement readings will be changing in real time as you point the binoculars at different objects. Message SCAN appears in the top right corner.
2. To exit SCAN mode, press UP (2) or LRF (21) button again.
3. If measurement fails, dashes will appear on the display.
4. In 4 seconds of inactivity (no measurement is taken) the rangefinder turns off, the rangefinding reticle with readings disappears from the display.

Notes:

• To select a rangefinding reticle, please see the Reticle Type subsection in the Rangefinder section.
• To select a unit of measurement (meters or yards) go to the Units of Measure subsection of the General Settings section.

Additional Information:

• Accuracy of measurement and maximum range depend on the reflection ratio of the target surface, the angle at which the emitting beam falls on the target surface and environmental conditions. Reflectivity is also affected by surface texture, color, size and shape of the target. A shiny or brightly colored surface is normally more reflective than a dark surface.
• Measuring range to a small sized target is more difficult than to a large sized target.
• Accuracy of measurement can also be affected by light conditions, fog, haze, rain, snow etc. Ranging performance can degrade in bright conditions or when ranging towards the sun.

The device has a function enabling wireless communication with external devices (smartphone or tablet) via Wi-Fi.

• Turn on the wireless module in the WI-Fi Activation  menu option.

Wi-Fi operation is shown in the status bar as follows:

Connection status	Status bar indication
Wi-Fi is off
Wi-Fi activated by the user, Wi-Fi in the device is being activated
Wi-Fi is on, no connection with device
Wi-Fi is on, device connected

• Your device is detected by an external device as “Accolade 2 LRF_XXXX”, where XXXX – is the last four digits of device’s serial number.
• After entering the password (default: 12345678) on an external appliance (see Password Setup subsection of the Wi-Fi Settings section for more information on setting a password) and connection is established, the icon  in the status bar changes to .

Accolade 2 LRF Pro thermal imaging binoculars feature video recording and photography of the image being ranged to the internal memory card.

Before using this feature, please read the Date and Time subsections of the section General Settings.

The built-in recorder operates in two modes – Video and Photo.

Video mode. Video recording 

1. Switch to Video mode by pressing and holding the REC (4) button.
2. In the top left corner you will see icon  and remaining recording time in the format HH:MM (hours: minutes).
3. Start video recording with a short press of the REC (4) button.
4. Upon start of video recording icon  disappears, and icon REC and recording timer in the format MM:SS (minutes : seconds) appear instead: .
5. Pause and resume recording video with a short press of the REC (4) button.
6. Stop recording video with a long press of the REC (4) button.
7. Video files are saved to the memory card after stopping video.
8. Switch between modes (Video-> Photo-> Video) with a long press of the REC (4) button.

Photo mode. Capturing an image 

1. Switch to the Photo mode with a long press of the REC (4) button.
2. Take a picture with a brief press of the REC (4) button. The image freezes for 0.5 sec and a photo is saved to the internal memory.
3. In the top left corner of the display you can see: photography icon , “>100” means that you can take more than 100 pictures. If the number of available pictures is less than 100, actual amount of available pictures (for example 98) is shown next to the icon .

Notes:

• You can enter and operate the menu during video recording.
• Recorded videos and photos are saved to the built-in memory card in the format img_xxx.jpg (photos); video_xxx.avi (videos). xxx – three digit counter for videos and photos.
• Counter for multimedia files cannot be reset.

Attention!

• The maximum duration of a recorded file is five minutes. After this time expires, a video is recorded into a new file. The number of recorded files is limited by the capacity of the device’s internal memory.
• Check regularly the free capacity of the internal memory, move recorded footage to other storage media to free up space on the internal memory card.
• When the Display Off function is activated, video recording is paused.

Important!

To playback video files recorded by thermal imaging devices on macOS based computers, we recommend that you use VLC video player or Elmedia player.

Download links are shown below:

VLC Video Player

http://www.videolan.org/vlc/download-macosx.html

ELMEDIA Video Player

https://apps.apple.com/us/app/elmedia-multiformat-video/id937759555?mt=12

This feature is not supported on devices manufactured after August 1, 2021.

(Bought separately)

Wireless remote control (RC) duplicates the power on function, digital zoom, rangefinder control, and menu navigation.

	Controller (18)	Button ON (19)	Button ZOOM (20)	Button LRF (21)
Brief press	Enter the quick menu	Turn on the device / Calibrate the microbolometer	Activate incremental zoom	Activate rangefinder / Measure distance
Long press	Enter the main menu	Display Off / Turn off the device	Activate function PiP	Activate SCAN mode
Clockwise rotation	Increase parameter, move upwards
Counterclockwise rotation	Decrease parameter, move downwards

1. Connect one end of the USB cable (16) to the Micro-USB (15) port of your device, and the other end to the USB port of your PC/laptop.
2. Turn the device on with a short press of the ON/OFF (1) button (device that has been turned off cannot be detected by your computer).
3. Your device will be detected by the computer automatically; no drivers need to be installed.
4. Two connection modes will appear on the display: Power and Memory Card (external memory).
5. Select connection mode with UP (2)/DOWN (5) buttons.
6. Confirm selection with a short press of the Menu (3) button.

Connection modes:

Power

• In this mode, when a computer is used as an external power supply, the icon  appears in the status bar. The device will continue operating and all functions are available.
• The Battery pack installed in the device is not being charged!
• When disconnecting from the computer, the device will continue to operate from the battery pack (if it is present and holding enough charge).​

Memory Card (external memory)

• In this mode the device is detected by the computer as a flash card. This mode is designed for work with the files saved in device’s memory. The device’s functions are not available in this mode; the device turns off automatically.
• If video recording was in progress when connection was made, recording stops and video is saved.
• When USB is disconnected from the device where connection is in the Memory Card mode, the device remains on the OFF state. Turn the device on for further operation.

1. Download free of charge Stream Vision App on Google Play or App Store.
2. Connect your Pulsar device to your mobile device (smartphone or tablet).
3. Launch Stream Vision and go to section “My Devices”.
4. Select your Pulsar device and press “Check Updates”.
5. Wait for the update to download and install. Pulsar device will reboot and will be ready to operate.

Important:

• if your Pulsar device is connected to phone, please turn on mobile data transfer (GPRS/3G/4G) to download update;
• if your Pulsar device is not connected to your phone but it’s already in the “My Devices” section, you may use Wi-Fi to download update.

Find answers to frequently asked questions about using Stream Vision here.

Is your firmware up to date?

Click here to check the latest firmware for your device.

Stream Vision 2

1. Download free Stream Vision 2 App in Google Play or App Store.
2. Connect your Pulsar device to your mobile device (smartphone or tablet).
3. Launch Stream Vision 2 and go to section “Settings”.
4. Select your Pulsar device and press “Check firmware update”.
5. Wait for the update to download and install. Pulsar device will reboot and will be ready to operate.

Important:

• if your Pulsar device is connected to phone, please turn on mobile data transfer (GPRS/3G/4G) to download update;
• if your Pulsar device is not connected to your phone but is already listed in “Settings” > “My devices” section, you may use Wi-Fi to download update.

Find answers to frequently asked questions about using Stream Vision 2 here.

Accolade 2 LRF Pro thermal imaging binoculars support Stream Vision technology which allows you to stream an image from the display of your thermal imager to a smartphone or tablet PC via Wi-Fi in real time mode.

You can find further guidelines on Stream Vision here.

Download from Google Play

Download from App Store

Find answers to frequently asked questions about using Stream Vision here.

Maintenance should be carried out no less frequently than twice a year, and should consist of the following measures:

• Wipe the exterior surfaces of metal and plastic parts off dust and dirt with a cotton cloth. To avoid damage to the paint coating, do not use chemically active substances, solvents, etc.
• Clean the electric terminals of the Battery Pack and device’s battery slot using a grease-free organic solvent.
• Check the objective and eyepieces lenses; rangefinder’s emitter and receiver lenses. If required, remove dust and sand (preferably by a noncontact method). Clean the external surfaces of the lenses with products expressly designed for this purpose.
• Always store the device in its carrying case in a dry, well-ventilated space. Remove the Battery Pack for long-term storage.

It is recommended to carry out a technical inspection before each use of the device. Check the following:

• External view (there should be no cracks on the housing).
• The state of the objective, eyepiece and rangefinder lenses (there should be no cracks, spot, dust, deposits etc.).
• The state of the rechargeable battery (should be charged) and the electric contacts (should be no signs of salts, oxidation or debris).
• Correct functioning of the controls.